Product Description
This is a 1.0 m³ reinforced rock bucket built for the Hyundai R215 class excavator — the bucket size most contractors pick when the machine spends its week in broken rock instead of topsoil. A standard 1 m³ digging bucket carries enough volume but not enough wall: in blasted limestone, demolition rubble and compacted hardpan the lip, the wings and the teeth wear out long before the shell has any right to. The reinforced version answers that with heavier plate on the side walls and the bowl, full-length reinforcement ribs on both wings, and a wear package that is meant to be replaced rather than written off.The cutting edge is built for it: five cast KW300RC rock teeth on a heavy lip, a bolt-on 90×45 wear edge under the teeth, and bolt-on side cutters on both corners. Teeth are changed one at a time on pinned adapters, the wear edge and cutters come off with hand tools, and the shell goes back to work without a cutting torch. That is the difference between a same-day change in the yard and a welding job on site.
The shell is Q345B plate from a first-class steel plant, laser cut, welded in a fixture and ground; the hitch bores are machined after welding so the machine pins fit without shims. The bowl is deep and radiused with a large open area and stowing surface, so blasted rock releases cleanly on the dump instead of packing. Built to the Hyundai R215 hitch drawing — pin-on or quick coupler — and available in your own colour and marking.
Model R215-1.0 / Reinforced — finished 1 m³ rock bucket, painted and ready for the hitch, standing in the assembly bay beside a matching ripper.
R215-1.0 · three-quarter view — five-tooth cutting edge, side cutters on both corners and reinforcement ribs welded down the wing. |
R215-1.0 · inner bowl — deep radiused bowl with a large open area and stowing surface, so rock and wet spoil drop clean. |
R215 · hitch end — four bored ears to the R215 hitch drawing, machined after welding, greased at each boss. |
R215-1.0 · mouth view — the five-tooth edge and the bolt-on wear edge behind it, both replaceable on the machine. |
KW300RC · tooth detail — cast rock tooth with the pin-on nose, seated on its adapter; one tooth, one pin, one swap. |
R215-1.0 · side view — reinforced wing plate, hook and rib on the face that scrapes the trench wall. |
Pre-paint · R215 marking — the reinforced shell before paint: wing ribs, bolt-on wear edge, tooth adapters welded out. |
R215-1.0 · inside the shell — wear strips laid along the bowl and the top rail, where rock rides hardest. |
R215 · pin bosses — bores machined after the shell is welded, so the pin pulls in tight instead of developing play. |
R215 · hitch detail — ear plate thickness, weld profile and bore finish on the machine side of the bucket. |
R215 · shell build — 1 m³ reinforced shell in the fixture, ribs and side walls welded out before grinding. |
R215 · adapter welding — five KW300RC adapters welded to the lip, then the teeth pinned on after paint. |
Application
- Rock and shot-rock loading — loading blasted limestone, granite and basalt from the muck pile into trucks or crusher feed. The 1 m³ bowl with its wide mouth and five rock teeth keeps the cycle short and holds the fines that a narrow bucket loses over the spill guard.
- Demolition and concrete removal — slabs, footings, columns and reinforced concrete. The teeth pry, the 90×45 wear edge takes the abrasion, and the shell is still serviceable when the project ends.
- Rock trenching and hardpan — utility and drainage trenches through rock, caliche and compacted hardpan, where the side cutters and reinforced wings do the cutting and the bowl keeps the line clean.
- Road cut and site preparation — cut and fill, rock clearance and verge work for a 21-ton class machine. The same shell also dresses stockpiles and loads out spoil between rock jobs.
- Riprap and boulder placement — armour stone on embankments, river banks and drainage works, where a controlled dump from a deep bowl matters as much as breakout force.
-
Slag, scrap and abrasive bulk — foundry slag, mill scale and mixed scrap, handled with a wear package that is renewed tooth by tooth and edge by edge rather than replaced as a unit.
Features
- 1.0 m³ reinforced shell for the R215 class — bucket volume sized to the Hyundai R215, with the side walls and bowl built heavier than a standard 1 m³ digging bucket so the shell outlasts the rock it works in.
- Full-length wing reinforcement — ribs run the height of both side walls and carry through to the corners, which is where a rock bucket usually cracks first. Extra plate and gussets protect the wall that scrapes the trench side.
- Five KW300RC cast rock teeth — pinned onto welded adapters on a heavy lip. Spacing and profile are set for broken rock, so the teeth bite and pry instead of skidding across the face. A broken or dulled tooth is swapped on site with a pin and a hammer.
- Bolt-on 90×45 wear edge — a replaceable strip bolted under the teeth, so the lip itself is not consumed. When the edge is spent, the bolts come out and a new one goes on without cutting the shell.
- Bolt-on side cutters — renewable cutters on both corners, taking the corner wear that would otherwise grind the wing plate away. Reversible and replaceable in the yard.
- Q345B body with wear plate where it rubs — structural plate from a first-class steel plant for the shell, with wear strips laid along the bowl and top rail where rock actually rides.
- Deep radiused bowl, large open area — the smooth bowl and wide stowing surface let blasted rock and wet spoil release cleanly on the dump instead of packing into the corners.
- Machined pin joints and grease points — hitch bores are machined after welding and every pin boss carries its own grease point, so the bucket stays tight under load rather than developing play.
- R215 pin-on hitch or quick coupler — built to the Hyundai R215 pin diameter, arm width and centre-to-centre, or fitted with an S-type, HS-type or grab-type coupler interface.
-
Paint and marking to your fleet — the yellow shown is our own, and black, green, red or a matched colour are equally available, with your branding and part number marked on the shell.
Product Parameters
| Product Name | Hyundai R215 1.0 m³ reinforced rock bucket for excavators |
| Model | R215-1.0 (1 cubic metre reinforced type) |
| Suitable Machine | Hyundai R215 crawler excavator; other 20–22 t class machines on request |
| Bucket Capacity | 1.0 m³ — 0.1–12 m³ available across the range |
| Bucket Type | Reinforced heavy duty rock bucket (standard duty also available) |
| Teeth | 5 × KW300RC cast rock teeth on welded adapters |
| Wear Parts | Bolt-on 90×45 wear edge under the teeth, bolt-on side cutters at both corners |
| Material | Q345B purchased from a first-class steel plant |
| Production Standard | OEM / built to customer drawing, sample or OEM part number |
| Process | Laser Cutting, Welding, Grinding |
| Welding Quality | Straight and Tight |
| Finish | Smooth, painted |
| Painting Color | Yellow as shown, or Black or Green or Red, etc (painting as customers' request) |
| Quality Guarantee | 6 months |
| Certification | ISO9001; TS and CE |
| Delivery Time | Within 10–20 days after sales contract establishment |
| Package | Fumigate seaworthy packing and Export Standard Package |
| Payment Term | TT, L/C, Paypal, Western Union, D/P |
| Usage | Crawler Backhoe Excavator |
Why Choose us?
| Hyundai | Excavator | R55, R80, R110, R140, R160, R180, R210, R215, R220, R250, R290, R300, R330, R360, R380, R430, R480, R520, R800 |
| Caterpillar | Excavator | E320, E320D, E320E, E323, E330, E330D, E336, E345DL, E349DL, E374, E395, E305.5, E308, E312, E315 |
| Komatsu | Excavator | PC55, PC70, PC130, PC200, PC220, PC240, PC300, PC350, PC400, PC450, PC650, PC800, PC1250 |
| Hitachi | Excavator | ZX55, ZX70, ZX120, ZX130, ZX200, ZX210, ZX240, ZX250, ZX330, ZX350, ZX470, ZX670, ZX870, ZX1200, EX200, EX300, EX400 |
| Kobelco | Excavator | SK55, SK75, SK130, SK140, SK170, SK200, SK210, SK210LC-8, SK220, SK250, SK260, SK300, SK330, SK350, SK480, SK500, SK850 |
| JCB | Excavator | JS130, JS145, JS160, JS200, JS220, JS235, JS300, JS330, JS370, JS460 |
| Doosan | Excavator | DX55, DX60, DX80, DX140, DX150, DX170, DX200, DX225, DX235, DX255, DX300, DX340, DX350, DX380, DX420, DX480, DX520, DX530, DX700, DX800 |
| Daewoo | Excavator | DH55, DH60, DH80, DH130, DH150, DH170, DH200, DH220, DH225, DH258, DH280, DH300, DH320, DH360, DH370, DH420, DH500 |
| New Holland | Excavator | E18, E26, E33, E37, E55, E60, E75, E135, E145, E175, E215, E230, E260, E305, E335, E385, E485 |
| Shantui | Excavator | SE60, SE75, SE135, SE150, SE210, SE215, SE220, SE240, SE260, SE335, SE370, SE470, SE500 |
| JCB | Backhoe Loader | 1CX, 2CX, 3CX, 4CX, 5CX |
| Komatsu | Wheel Loader | WA100, WA150, WA200, WA250, WA320, WA380, WA430, WA470, WA500, WA600, WA800, WA900 |
The R215-1.0 bucket shown on this page fits the Hyundai R215. Other models in the list are built to the same design in the capacity and hitch that suits them — send the machine model and we confirm the matching bucket.
FAQ
Q1: Will this 1 m³ bucket fit my Hyundai R215, and how do I confirm the hitch?
A:
It is built to the R215 hitch: pin-on to the OEM pin diameter, arm width and centre-to-centre, or fitted with a quick coupler. Send us the machine model and serial or the three hitch dimensions — pin diameter, arm width, pin centre distance — and we confirm the interface before quoting. If you already run a coupler, tell us the type (S-type, HS-type or grab-type) and we match it.
Q2: Why the reinforced version instead of a standard 1 m³ bucket?
A:
On rock the standard shell is the part that fails first — the wings crack at the corners and the bowl wears thin behind the teeth. The reinforced bucket adds plate thickness on the side walls and bowl, full-length ribs down both wings, and a replaceable wear edge and side cutters, so the money goes into the wear parts instead of a new bucket every season.
Q3: What happens when the teeth or the edge wear out?
A:
The five KW300RC teeth are pinned to welded adapters and are changed one at a time on the machine. The 90×45 wear edge under the teeth and the side cutters at both corners are bolt-on, so they come off with hand tools rather than a torch. Teeth, adapters, wear edges, cutters and pins are kept in stock, so a replacement set can ship with your next order.
Q4: Can you build a different capacity or width for the same machine?
A:
Yes. The range runs from 0.1 to 12 m³, and shell width, wing height, tooth count, tooth pattern, wear plate layout and hitch dimensions are all built to your drawing, sample or OEM part number. If your ground is heavier than usual — larger rock, more abrasive stone — we will advise on a narrower or wider bucket and a heavier wear package before you order.
Q5: What is the lead time, packing, payment and warranty?
A:
Standard lead time is 10–20 days after the sales contract, packed in fumigated seaworthy crates to export standard and braced in the container, with loading photos sent before the container is sealed. Payment by T/T, L/C, PayPal, Western Union or D/P. The quality guarantee is six months, and production is ISO9001 certified with TS and CE documentation available for the shipment.















